The PT2X Wet / Wet Differential Smart Sensor with integrated datalogger is the latest in pressure measurement technology. It contains two diaphragms which detect the difference between the pressure on the high side and the pressure on the low side.
The PT2X Wet Wet Differential Smart Sensor comes with powerful Aqua4Plus software. This easy to use software gives the user extensive control, including flexible programming, easy field calibration, real time monitoring and a delayed start feature.
This device is capable of networking several PT2X Wet/Wet sensors, or a combination of Smart Sensors together and control them from a single computer or wireless telemetry system.
Other features:
Manufactured by: INW
Model: PT2X Wet/Wet Differential Smart Sensor with Data logging
Used to replace analog sensors with separate data loggers
In pressure equalization applications, in corrosive and liquid environments
Flow measurement
GENERAL | |
Length | 13.55" (34.4 cm) cabled 13.272" (33.7 cm) cableless |
Diameter | 0.75" (1.9 cm) |
Weight | 0.8 lb. (0.4 kg) |
Body Material | Delrin® & 316 stainless steel or titanium |
Wire Seal Material | Viton® and PTFE/FEP |
Submersible Cable | Polyurethane, polyethylene, or FEP available |
Protection Rating | IP68, NEMA 6P |
Desiccant | 1-3 mm indicating silica gel (high or standard capacity) |
Terminating Connector | Available |
Communication | RS485 Modbus® RTU SDI-12 (ver.1.3) |
Direct Modbus Read Output | 32-bit IEEE floating point |
SDI-12 Output | ASCII |
Internal Math | 32-bit floating point |
Operating Temp. Range3 | -15° C to 55° C |
Storage Temp. Range1 | -40° C to 80° C |
LOGGING | |
Memory | 4MB - 520,000 records |
Log Types | Variable, user-defined, logarithmic, profiled |
Programmable Baud Rate | 9600, 19200, 38400 |
Logging Rate | 8x/sec maximum |
Software | Complimentary Aqua4Plus or Aqua- 4Push |
Networking | 32 available addresses per junction w/ batching capabilities (up to 255) |
File Formats | .xls / .csv / .a4d |
POWER | |
Internal Battery | 2x1.5V AA alkaline2 |
Auxiliary Power | 12 VDC - Nominal 6-15VDC - Range |
Exp. Alkaline Battery Life | 18 months at 15m polling interval5 |
TEMPERATURE | |
Element Type | Digital IC on board |
Accuracy | ± 0.5° C |
Resolution | 0.1° C |
Range | -40° C to 80° C |
Units | Celsius, Fahrenheit, Kelvin |
PRESSURE | |
Transducer Type | Silicon strain gauge |
Transducer Material | 316 stainless steel or titanium |
Pressure Ranges | PSID (differential) - 15, 30, 50, 100, 300, 500 mH2O (differential) - 10.5, 21, 35, 70, 210, 350 |
Common Mode Pressure | 10x range or 1000 PSI (whichever is lower) |
Units | PSI, FtH2O, inH2O, cmH2O, mmH2O, mH2O, inHg, cmHg, mmHg, Bars, mBars, kPa |
Static Accuracy | ± 0.05% FSO (typical) ± 0.1% FSO (maximum) (B.F.S.L. 20° C) |
Resolution | 0.0034% FS (typical) |
Maximum Operating Pressure | 1.1 x FS |
Burst Pressure4 | 3.0 x FS |
Compensated Range | 0° C to 40° C |
1 Storage without batteries 2 Lithium available upon request 3 Requires freeze protection kit if in water below freezing 4 Burst reduced at PSI>300 5 May vary due to environmental factors |
As the Levelogger App Interface will not connect directly to the top of a Solinst datalogger, it is necessary to have connection accessories. With the Levelogger or Rainlogger, one of the following accessories is required:
Leveloggers. Provides detailed information on the datalogger,
and includes options for running a self-test, doing a memory
dump and creating/emailing reports.